STUDER S 145 CNC二手数控内圆磨床进口宝鸡市的手续
Machine's group :CNC Internal grinder
Type :STUDER S 145 CNC
Controller :GE FANUC Series 16-T
Pdf (Print)
Information request
STUDER S 145 CNC
5 Image(s)
Back
Technical data
Swing diameter:
Above the workpiece table 350 mm
In front of the workpiece table 455 mm
Centre height 175 mm
Workpiece length max. 530 mm
Axial motion:
Longitudinal travel (Z-axis) 500 mm
cross travel (x axis) 120 mm
Work piece spindle head (B-axis) + / -30°
Feed range:
X axis (transversal) 0.001-10000 mm/min
Z axis (longitudinal travel) 0.001-10000 mm/min
C axis (spindle,resolution) 0.0001 °
Grinding spindle head:
Swivelling range 0 - 270 °
Number of positions 4
speeds:
stepless
from 5000 rpm
up to 120000 rpm
Work piece spindle head:
speeds:
stepless
from 1 rpm
up to 1000 rpm
Typing speed 1 - 50 rpm
Spindle hole 50 mm
taper in spindle: ISO 50
Work piece spindle nose CAMLOCK 6
Voltage 50 Hz 3x 400 Volt
Workpiece spindle motor 3.8 kW
Total power required 22 kVA
Machine's weight about 5700 kg
Overall dimensions machine:
Length 3000 mm
Width 2000 mm
Height 2200 mm
Various accessories:
B axis resolution max. 0.001 °
Wheel trueing attachment
Electronic grinding detection
Thread grinding cycles
Coolant system
Paper filter facility
Full splash cabin
Lamp
Status light
3-jaw chuck diameter mm
Electronic hand held control
Interface serial port RS 232
机床组别:数控内圆磨床 型号:STUDER S 145 CNC 控制器:GE FANUC系列16-T Pdf(打印) 信息请求 STUDER S 145数控机床 5张图片 背 技术数据 摆动直径: 工件台上方350 mm 工件台前455mm 中心高度175 mm 工件长度最大530mm 轴向运动: 纵向行程(Z轴)500 mm 横向行程(x轴)120 mm 工件主轴头(B轴)+/-30’ 进给范围: X轴(横向)0.001-10000 mm/min Z轴(纵向行程)0.001-10000 mm/min C轴(主轴,分辨率)0.0001’ 磨头: 旋转范围0-270’ 职位数4 速度: 无极 从5000转/分开始 高达120000转/分 工件主轴头: 速度: 无极 从1转/分开始 高达1000转/分 打字速度1-50转/分 主轴孔50 mm 主轴锥度:ISO 50 工件主轴前端凸轮锁6 电压50赫兹3 x 400伏 工件主轴电机3.8kw 所需总功率22 kVA 机器重量约5700公斤 机器外形尺寸: 长度3000 mm 宽度2000 mm 高度2200mm 各种配件: B轴分辨率最大为0.001° 车轮校正附件 电子磨削检测 螺纹磨削循环 冷却系统 纸过滤设备 全飞溅舱 灯 状态指示灯 三爪卡盘直径mm 电子手持式控制 接口串行端口RS 232